Skip to main content

Different Types of Traps.

Trap:- 
The trap can be defined as fittings at the end of soil pipes or waste pipes to stop foul gasses (odour) coming out of the soil pipe or waste pipe. 
In most homes, there is a P-trap installed under the sinks in the bathroom and kitchens. A P-trap is a plumbing fixture that has several purposes. It traps debris that has drained from the sink and prevents it from forming a clog deep within the plumbing system, and to stops sewer gases from passing into the home.
Types of Traps:- 

Traps - Types and Uses. A trap is a device which is used to prevent sewer gases from entering the buildings. The traps are located below or within a plumbing fixture and retains small amount of water. The retaining water creates a water seal which stops foul gases going back to the building from drain pipes.

1. Floor Trap: The purpose of a trap is to prevent foul-smelling sewer gas from coming back in to the house. ... The 'sewer' side will have sewer gases present, but the water sitting in the bottom of the trap prevents the sewer gases from entering in to the house. Floor DrainFloor drains are no exception.

2. Gully Trap: gully trap is provided outside the building before connecting to external sewerage line. It also collects waste water from the kitchen sink, wash basins, baths and wash area. Gully Trap is provided to prevent the foul gases entering in to the building by providing water seal.

3. P, Q and S-Trap: The reason for using a P trap is that the horizontal pipe can go through the wall and into a tee that goes both down to the main drain line and up to a roof vent. The S trap is banned because without venting, sewer gasses are more likely to enter the house.

4. Intercepting Trap: Intercepting trap is provided in to the Interceptor Manhole (Interceptor Chamber). An Interceptor manhole is provided at the intercept of building sewer and Public sewer.

Intercepting trap is provided to prevent the foul gases entering in to the building sewer by providing water seal. It has deep water seal of 100 mm depth and it also prevents entry of bugs and insects from sewer line to building sewer.

5. Bottle Trap: A bottle trap is provided to receive waste water from washbasin, kitchen sinks and other appliances where the appliances do not have built-in it trap. The bottle traps are normally cast in one piece in brass with copper content not less than 56 percent and then chromium plated or nickel-plated. It is also manufactured in PVC. Bottle traps are manufactured in 32mm/40mm diameter size and it is a general practice to provide internal threads on the inlet traps, and to facilitate connections to the waste couplings (bodies), use of inlet tailpipes and coupling nut. External threads are provided on the outlet in case of screwed outlet traps for connection to waste pipes.

Different Types of Traps.

6. Grease Trap: grease trap (also known as grease interceptorgrease recovery device, grease capsule and grease converter) is a plumbing device (a type of trap) designed to intercept most greases and solids before they enter a wastewater disposal system.
In the most basic terms, a grease trap works by slowing down the flow of warm/hot greasy water and allowing it to cool. As the water cools, the grease and oil in the water separate out and float to the top of the trap. The cooler water - minus the grease - continues to flow down the pipe to the sewer.

जाल:-
जाल को मिट्टी के पाइप या अपशिष्ट पाइप को रोकने के लिए मिट्टी के पाइप या अपशिष्ट पाइप के अंत में फिटिंग के रूप में परिभाषित किया जा सकता है।
ज्यादातर घरों में, बाथरूम और रसोई में सिंक के नीचे एक पी-जाल स्थापित होता है। एक पी-जाल एक नलसाजी स्थिरता है जिसके कई उद्देश्य हैं। यह मलबे को फँसाता है जो सिंक से निकल गया है और इसे प्लंबिंग सिस्टम के भीतर गहरी जमाव बनाने से रोकता है, और सीवर गैसों को घर में जाने से रोकता है।
जाल के प्रकार: -
जाल - प्रकार और उपयोग। जाल एक उपकरण है जिसका उपयोग सीवर गैसों को इमारतों में प्रवेश करने से रोकने के लिए किया जाता है। जाल नीचे या एक नलसाजी स्थिरता के भीतर स्थित हैं और पानी की छोटी मात्रा को बरकरार रखता है। रिटेनिंग वॉटर एक पानी की सील बनाता है जो नाली पाइपों से इमारत में वापस जाने वाली फाउल गैसों को रोकता है।

1. फ़्लोर ट्रैप: फेल-महक सीवर गैस को घर में वापस आने से रोकने के लिए एक जाल का उद्देश्य है। ... 'सीवर' की तरफ सीवर गैसें मौजूद होंगी, लेकिन जाल के तल में बैठा पानी सीवर गैसों को घर में प्रवेश करने से रोकता है। फर्श नाली। फर्श की नालियां कोई अपवाद नहीं हैं।

2. गली ट्रैप: बाहरी सीवरेज लाइन से जुड़ने से पहले इमारत के बाहर एक जालीदार जाल दिया जाता है। यह रसोई के सिंक, वॉश बेसिन, स्नान और धोने के क्षेत्र से अपशिष्ट जल भी एकत्र करता है। गली ट्रैप को पानी की मुहर प्रदान करके इमारत में प्रवेश करने से रोकने के लिए प्रदान किया जाता है।

3. पी, क्यू और एस-ट्रैप: एक पी जाल का उपयोग करने का कारण यह है कि क्षैतिज पाइप दीवार के माध्यम से और एक टी में जा सकता है जो दोनों मुख्य नाली लाइन तक और छत के वेंट तक जाता है। एस जाल पर प्रतिबंध लगा दिया गया है क्योंकि बिना वेंटिंग के, सीवर गेस घर में प्रवेश करने की अधिक संभावना है।

4. इंटरसेप्टिंग ट्रैप: इंटरसेप्टर जाल को इंटरसेप्टर मैनहोल (इंटरसेप्टर चैंबर) में प्रदान किया जाता है। एक इंटरसेप्टर मैनहोल सीवर और सार्वजनिक सीवर के निर्माण के अवरोधन पर प्रदान किया जाता है।
पानी की सील प्रदान करके इमारत के सीवर में प्रवेश करने वाली दुर्गंध गैसों को रोकने के लिए अवरोधक जाल प्रदान किया जाता है। इसमें 100 मिमी की गहराई में पानी की सील है और यह सीवर लाइन से बिल्डिंग सीवर तक कीड़े और कीड़े के प्रवेश को भी रोकता है।

5. बॉटल ट्रैप: वॉशबेसिन, किचन सिंक और अन्य उपकरणों से अपशिष्ट जल प्राप्त करने के लिए एक बॉटल ट्रैप प्रदान किया जाता है, जहाँ उपकरणों में अंतर्निहित ट्रैप नहीं होता है। बोतल के जाल को आमतौर पर पीतल के एक टुकड़े में रखा जाता है जिसमें तांबे की सामग्री 56 प्रतिशत से कम नहीं होती है और फिर क्रोमियम चढ़ाया जाता है या निकल चढ़ाया जाता है। यह पीवीसी में भी निर्मित है। बोतल के जाल 32 मिमी / 40 मिमी व्यास के आकार में निर्मित होते हैं और इनलेट जाल पर आंतरिक धागे प्रदान करने के लिए, और अपशिष्ट कपलिंग (निकायों) से कनेक्शन की सुविधा के लिए, इनलेट टेलपाइप और युग्मन अखरोट का उपयोग करना एक सामान्य अभ्यास है। अपशिष्ट पाइप के कनेक्शन के लिए स्क्रू आउटलेट जाल के मामले में आउटलेट पर बाहरी धागे प्रदान किए जाते हैं।

6. ग्रीस ट्रैप: एक ग्रीस ट्रैप (जिसे ग्रीस इंटरसेप्टर, ग्रीस रिकवरी डिवाइस, ग्रीस कैप्सूल और ग्रीज़ कन्वर्टर भी कहा जाता है) एक प्लंबिंग डिवाइस (एक प्रकार का ट्रैप) है जिसे अधिकांश ग्रीस और सॉलिड को इंटरसेप्ट करने के लिए डिज़ाइन किया गया है, जो एक अपशिष्ट निपटान प्रणाली में प्रवेश करता है।
सबसे बुनियादी शब्दों में, एक ग्रीज़ जाल गर्म / गर्म चिकना पानी के प्रवाह को धीमा करके और इसे ठंडा करने की अनुमति देकर काम करता है। जैसे ही पानी ठंडा होता है, पानी में मौजूद तेल और तेल अलग हो जाते हैं और जाल के ऊपर तैरने लगते हैं। कूलर का पानी - माइनस ग्रीस - पाइप से सीवर तक बहता रहता है।

Comments

Popular posts from this blog

Medlum Density Fibre Board (MDF)

Medium Density Fibre Board (MDF)  MDF IS made from wood and other lignocellulose material refined into fibres and reconstituted with a resin binder. Row wood material is normally a single species wood. MDF has homogeneous structure with uniform density, texture and properties throughout, no identifiable grain can be seen at edge, end or face. There are no internal voids or pits and there is no variation in the surface hardness. Unlike plywood MDF doesn't delaminate. It has much higher strength than particle board. Since edges are totally smooth and uniform, costly tipping or beading with strips of wood required for plywood and particle board is not essential. It can be carved, grooved or embossed just like any timber. The surface of MDF is totally smooth and accepts all kinds of finishes - paints, varnishes and laminates. One such type of famous board in the market is 'Duratuff" . It comes in both interior and exterior grade. Duratuff prelaminated boards are also avail...

The loads Acting on staircase.

Distribution of  Loads  and its Effect on  Staircase Stair  slabs are usually designed to resist gravity  loads , comprising of dead  loads  and live  loads  as described below:  1) Dead  Load : The components of the dead  load  to be considered are: a) Self-weight of  stair  slab (tread/tread-riser slab/waist slab) b) Self-weight of ... LIVE LOADS:- IS 875 parts II specifies the load to be considered as UDL of intensity 5KN/m2 for public  buildings and 3kN/m2 for residential building where the specified floor do not exceed 2kN/m2 and the staircases are should not liable for overcrowding. DEAD LOADS:- Self-weight of stair slab which includes the waist slab, tread-rise,etc. Self-weight of finishes (0.5 to 1 kN/m?) Types of stairs                                                ...

MACHINE FOUNDATION.

MACHINE FOUNDATION. The design of machine foundation involves careful study of the vibration characteristics of the foundation system. Relevant data for the design and construction of the foundation of machine should be obtained from the manufacturer of the machine , prior to the start design.  All parts of machine foundation should be designed for maxim stresses due to the worst combination of vertical loads, torque, longitudinal and transverse forces, stresses due to temperature variation and the foundation dead load. In case, the foundation layout is partly built up of beam and column construction , straight bars should be provided both at top and bottom of the beams and the spacing of the stirrups should be close. The main foundation block should have the designed thickness and should be reinforced both at top and bottom even if the reinforcements are not required from design considerations. Machine foundations  are special types of  foundations  required fo...