Skip to main content

Mosaic or Terrazzo flooring.

Mosaic or Terrazzo flooring.
The terrazzo flooring consists of two layers; the bottom layers of 2 cm cement concrete 1:2:4 or 1:1.5:3 as specified, and the upper layer of 6 mm thick consisting of a mix of marble chips and Cement should be of standard Specifications. The marble chips should be of 3 mm gauge, having maximum size 3 mm and minimum 1.5 mm. The sand should be coarse and well graded, clean and free from dust and dirt, etc. 
The stone girit (Shingle or bajri) should be hard and tough (granite stone) 13 mm gauge.
It should be clean and free from dust and dirt, etc. 32 mm (1) thick cement concrete (under layer) shall be aid in accordance with the instruction laid down in specification no.7. Dividing strips where required, including any strips in decorative design shall be bedded into the base concrete in case of ground floor. The top of the strips shall be kept at slightly higher level above the finished level of the floor, so that after grinding they are at the correct level.

Floor mosaics are made from small round pieces of stones. They form design pattern and give a beautiful look to the room. ... A mosaic is an art form using small pieces of colored stones, tiles, or glass to render an artful design.


Terrazzo is a composite material, poured in place or precast, which is used for floor and wall treatments. It consists of chips of marble, quartz, granite, glass, or other suitable material, poured with a cementitious binder (for chemical binding), polymeric (for physical binding), or a combination of both.


The permixed cement and pigment shall be mixed dry with marble chips in the ratio of 1 cement and 1.5 marble chippings The texture shall be well turned over adding just enough water to obtain a fairly dry but workable mixture.
The cement and marble mixture shall then be laid on the under layer (cement concrete) in a slightly more than 6 mm (.25"), thickness so that after rubbing down, the finished face is not less than 6 mm in thickness. 
Laying of top layer shall closely follow laying of under layer, so that the tow layers merge and firmly grip each other. 
The surface of the top layer shall be tamped and brought down to the required levels by using a straight edge. Immediately after completing the tamping, the surface shall be floated and trowelled once twice.
No attempt shall be made to remove the trowel marks. Borders and decorative designs shall be laid before the main body of the flooring. After two hours, the surface should be covered with wet gunny bags and. lefl undisturbed for two days. The surface shall then be cut by rubbing with sand stone blocks and all cement in the surface removed. A neat cement wash shall then be given and left undisturbed for six or seven days and then the surface should be ground (or rubbed) with carborundom stones of different grades starting with coarse one and successively with finer ones land rubbing should be continued until the entire surface shows e uniform granular appearance.

Terrazzo is solid floor. It is Portland cement mixed with marble chips and it is poured like concrete. It is then grinded and polished to a gloss. Mosaic is a type of tile pattern where different shapes of tile (either broken pieces of tile or cut pieces of tile) are laid in a pattern.

मोज़ेक या टेराज़ो फर्श।
टेराज़ो फ़्लोरिंग में दो परतें होती हैं; नीचे 2 सेमी सीमेंट कंक्रीट 1: 2: 4 या 1: 1.5: 3 की परतों के रूप में निर्दिष्ट किया गया है, और 6 मिमी मोटी की ऊपरी परत संगमरमर के चिप्स और सीमेंट के मिश्रण से मिलकर मानक विनिर्देशों की होनी चाहिए। संगमरमर के चिप्स 3 मिमी गेज के होने चाहिए, जिसमें अधिकतम आकार 3 मिमी और न्यूनतम 1.5 मिमी होगा। रेत को मोटे और अच्छी तरह से वर्गीकृत किया जाना चाहिए, साफ और धूल और गंदगी से मुक्त होना चाहिए, आदि।
पत्थर की गिरीट (शिंगल या बाजरी) सख्त और सख्त (ग्रेनाइट पत्थर) 13 मिमी गेज होनी चाहिए।
यह साफ और धूल और गंदगी से मुक्त होना चाहिए, आदि 32 मिमी (1) मोटी सीमेंट कंक्रीट (परत के नीचे) विनिर्देश संख्या 7 में दिए गए निर्देश के अनुसार सहायता करेगा। जहाँ आवश्यक हो, विभाजन वाली स्ट्रिप्स जिसमें सजावटी डिज़ाइन में कोई स्ट्रिप्स शामिल हैं, को भूतल के मामले में बेस कंक्रीट में बेड किया जाएगा। स्ट्रिप्स के शीर्ष को मंजिल के समाप्त स्तर से थोड़ा ऊपर के स्तर पर रखा जाएगा, ताकि पीसने के बाद वे सही स्तर पर हों।

फर्श मोज़ाइक पत्थरों के छोटे गोल टुकड़ों से बनाए जाते हैं। वे डिज़ाइन पैटर्न बनाते हैं और कमरे को एक सुंदर रूप देते हैं। ... एक मोज़ेक एक कला का रूप है जो एक कलात्मक डिजाइन को प्रस्तुत करने के लिए रंगीन पत्थरों, टाइलों या कांच के छोटे टुकड़ों का उपयोग करता है।

Terrazzo एक मिश्रित सामग्री है, जिसे जगह या प्रीकास्ट में डाला जाता है, जिसका उपयोग फर्श और दीवार उपचार के लिए किया जाता है। इसमें संगमरमर, क्वार्ट्ज, ग्रेनाइट, कांच, या अन्य उपयुक्त सामग्री के चिप्स होते हैं, जो सीमेंटेड बाइंडर (रासायनिक बंधन के लिए), बहुलक (भौतिक बंधन के लिए), या दोनों के संयोजन के साथ डाले जाते हैं।

अनुमत सीमेंट और पिगमेंट को 1 सीमेंट और 1.5 संगमरमर चिपिंग के अनुपात में संगमरमर के चिप्स के साथ सुखाया जाएगा। बनावट काफी अच्छी तरह से सूखा लेकिन व्यावहारिक मिश्रण प्राप्त करने के लिए पर्याप्त पानी जोड़ने पर अच्छी तरह से बदल जाएगी।
सीमेंट और संगमरमर का मिश्रण तब 6 मिमी (.25 ") से थोड़ा अधिक में परत (सीमेंट कंक्रीट) पर रखा जाएगा, ताकि नीचे रगड़ने के बाद, तैयार चेहरा मोटाई में 6 मिमी से कम न हो।
शीर्ष परत का बिछाने, परत के नीचे बिछाने का बारीकी से पालन करेगा, ताकि टो परत विलय हो जाए और एक दूसरे को मजबूती से जकड़ें।
ऊपरी परत की सतह को सीधा किनारे का उपयोग करके टेंप किया जाएगा और आवश्यक स्तरों तक लाया जाएगा। टेंपिंग को पूरा करने के तुरंत बाद, सतह को एक बार दो बार उतारा और प्रवाहित किया जाएगा।
ट्रॉवेल के निशान को हटाने का कोई प्रयास नहीं किया जाएगा। फर्श के मुख्य निकाय से पहले बॉर्डर और सजावटी डिजाइन रखे जाएंगे। दो घंटे के बाद, सतह को गीले गनी बैग के साथ कवर किया जाना चाहिए और। दो दिनों के लिए बिना किसी बाधा के। फिर सतह को हटाए गए सतह में रेत पत्थर के ब्लॉक और सभी सीमेंट के साथ रगड़कर सतह को काट दिया जाएगा। फिर एक साफ सीमेंट वॉश दिया जाएगा और छह या सात दिनों के लिए उसे छोड़ दिया जाएगा और फिर सतह को जमीन (या रगड़) से अलग-अलग ग्रेड के कार्बोरंडम पत्थरों से तैयार किया जाना चाहिए, जो मोटे तौर पर एक से शुरू होता है और बारीक लोगों के साथ जमीन की रगड़ को तब तक जारी रखा जाना चाहिए जब तक कि पूरी तरह से चालू न हो जाए। सतह से पता चलता है कि एकसमान दानेदार उपस्थिति है।
Terrazzo ठोस मंजिल है। यह पोर्टलैंड सीमेंट संगमरमर के चिप्स के साथ मिश्रित है और इसे कंक्रीट की तरह डाला जाता है। फिर इसे पीसकर एक पॉलिश से पॉलिश किया जाता है। मोज़ेक एक प्रकार का टाइल पैटर्न है जहाँ टाइल के विभिन्न आकार (या तो टाइल के टूटे हुए टुकड़े या टाइल के कटे हुए टुकड़े) को एक पैटर्न में रखा जाता है।

Comments

Popular posts from this blog

Medlum Density Fibre Board (MDF)

Medium Density Fibre Board (MDF)  MDF IS made from wood and other lignocellulose material refined into fibres and reconstituted with a resin binder. Row wood material is normally a single species wood. MDF has homogeneous structure with uniform density, texture and properties throughout, no identifiable grain can be seen at edge, end or face. There are no internal voids or pits and there is no variation in the surface hardness. Unlike plywood MDF doesn't delaminate. It has much higher strength than particle board. Since edges are totally smooth and uniform, costly tipping or beading with strips of wood required for plywood and particle board is not essential. It can be carved, grooved or embossed just like any timber. The surface of MDF is totally smooth and accepts all kinds of finishes - paints, varnishes and laminates. One such type of famous board in the market is 'Duratuff" . It comes in both interior and exterior grade. Duratuff prelaminated boards are also avail...

AN INTRODUCTION TO HPL

What is hpl Decorative High Pressure Laminates (HPL), as defined by the European and international standards for HPL, EN 438 and ISO 4586, are high-density panels (≥1.35g/cm3), finished and ready for use, which have exceptional mechanical, physical strength and chemical resistance, are easy to work and simple to maintain. Arpa HPL panels are made of several layers of cellulose fibre material impregnated with thermosetting resins and then simultaneously subjected to both pressure (>7MPa)) and heat (140 / 150°C) in special presses, for a fixed time, which varies depending on the type of laminate. This process creates a stable, inert, homogeneous, nonporous and high density material, with physical and chemical properties that are totally different from those of its original ingredients. In addition, given its very low permeability, HPL acts as a barrier against the possible emission of formaldehyde and other volatile substances (VOCs) from any timber substrates it is applied to. Compos...

How to Calculate Cost and Quantity of 1000 Sq.ft Concrete Slab?

Cost and Quantity of 1000 Sq.ft Concrete Slab 1000 Sq.ft = 92.93 Sq.mt. Thickness of Slab = 0.150 Sq.mt. Volume of Slab = 92.93 X 0.150 = 13.939 cu.mt. Beam Volume = 20% o f concrete Vol.                         =13.939 X 20/100 = 2.7878 cu.mt. Total Slab Volume = 13.939 + 2.7878 = 16.768 = 17 cu.mt. We know :- M20 Grade of Concrete (1 : 1.5 : 3)  Concrete  Quantity  of 1 cu.mt. Cement = 8 bags   Sand = 15 cu.ft  aggregate = 30 cu.ft  1 cu.mt Concrete Cost =  4,550 Rs. So :- M20 Grade of Concrete (1 : 1.5 : 3)  Concrete  Quantity  of 1000 cu.mt. Cement = 17 X 8 = 136 bags  Sand = 17 X 15 = 255 cu.ft  aggregate = 30 X 17 = 510 cu.ft 1000 cu.mt Concrete Cost =  77,350 Rs. Steel Quantity = 1% of concrete Vol.                          =17 X 1/100 =...