Skip to main content

WALLPAPER HANGING GUIDE

BEFORE 

· Remember to account for pattern repeat
· Always use paste suitable for non-woven wallpaper
· Check that all rolls of wallpaper have the same batch number. Be sure to buy enough rolls with matching batch numbers in order to get the same colour on all rolls (the batch number is printed on the label).
· If you have large colour differences on wall, the wall must be primed before hanging the wallpaper (primarily when using bright wallpaper).

TOOLS

Following tools are good too have
  1. Scissors
  2. Pencil
  3. Roller
  4. Paint Brush
  5. Tray
  6. A bowl of Water
  7. Sponge
  8. Spatula
  9. Scraper
  10. A sharp Knife

GUIDE

A. Apply paste onto the wall with a roller. Put on paste for about 2-3 lengths at a time. Use a brush to apply paste by ceiling, floor and edges.
B. Pull up one length of wallpaper directly from the roll/floor, and hang it on the pasted wall. Make sure you have a few extra centimeters of wallpaper at the ceiling and floor and make sure that the wallpaper hangs straight.
C. Make sure that the wallpaper hangs correctly by hanging a pair of scissors on a string from the ceiling.
D. Smooth the section of wallpaper from the top down and from the centre outwards. Use a wallpaper brush or spatula and make sure that all air bubbles are removed.
E. Trim excess wallpaper using a sharp wallpaper knife.
F. Hang the next section by butting the edges together. Make sure that the pattern matches across the two sections. Wash away excess paste with a damp, soft sponge. Do not rub.

AFTER
· Make sure to ventilate the room well to make the wallpaper dry.
· The wallpaper is washable. If needed, wipe off with a damp sponge.
· Wipe off vertically and do not rub.

इससे पहले

· पैटर्न दोहराने के लिए याद रखें
· हमेशा गैर-बुना वॉलपेपर के लिए उपयुक्त पेस्ट का उपयोग करें
· जांचें कि वॉलपेपर के सभी रोल में एक ही बैच नंबर है। सभी रोल पर समान रंग प्राप्त करने के लिए बैच नंबर के साथ पर्याप्त रोल खरीदना सुनिश्चित करें (लेबल पर बैच नंबर मुद्रित है)।
· यदि आपके पास दीवार पर बड़े रंग के अंतर हैं, तो वॉलपेपर लटकाए जाने से पहले दीवार को भड़कना चाहिए (मुख्य रूप से उज्ज्वल वॉलपेपर का उपयोग करते समय)।

उपकरण

निम्नलिखित उपकरण बहुत अच्छे हैं
कैंची
पेंसिल
बेलन
पेंट ब्रश
ट्रे
पानी का एक कटोरा
स्पंज
रंग
खुरचनी
एक तेज चाकू

मार्गदर्शक

A. दीवार पर एक रोलर के साथ पेस्ट लागू करें। एक बार में लगभग 2-3 लंबाई के लिए पेस्ट लगाएं। छत, फर्श और किनारों से पेस्ट लगाने के लिए ब्रश का उपयोग करें।
B. रोल / फर्श से सीधे वॉलपेपर की एक लंबाई खींचें, और इसे चिपकाई गई दीवार पर लटका दें। सुनिश्चित करें कि आपके पास छत और फर्श पर वॉलपेपर के कुछ अतिरिक्त सेंटीमीटर हैं और सुनिश्चित करें कि वॉलपेपर सीधे लटका हुआ है।
सी। सुनिश्चित करें कि वॉलपेपर छत से एक स्ट्रिंग पर कैंची की एक जोड़ी लटकाकर सही ढंग से लटका हुआ है।
डी। ऊपर और नीचे से केंद्र से वॉलपेपर के अनुभाग को चिकना करें। वॉलपेपर ब्रश या स्पैटुला का उपयोग करें और सुनिश्चित करें कि सभी हवाई बुलबुले हटा दिए जाते हैं।
ई। एक तेज वॉलपेपर चाकू का उपयोग करके अतिरिक्त वॉलपेपर ट्रिम करें।
एफ। किनारों को एक साथ जोड़कर अगले अनुभाग को लटकाएं। सुनिश्चित करें कि पैटर्न दो वर्गों में मेल खाता है। नम, नरम स्पंज के साथ अतिरिक्त पेस्ट को धो लें। मलो मत।

उपरांत
· वॉलपेपर को शुष्क बनाने के लिए कमरे को अच्छी तरह से हवादार करना सुनिश्चित करें।
· वॉलपेपर धोने योग्य है। जरूरत पड़ने पर नम स्पंज से पोंछ दें।
· लंबवत पोंछें और रगड़ें नहीं।
                         
         

Comments

Popular posts from this blog

AN INTRODUCTION TO HPL

What is hpl Decorative High Pressure Laminates (HPL), as defined by the European and international standards for HPL, EN 438 and ISO 4586, are high-density panels (≥1.35g/cm3), finished and ready for use, which have exceptional mechanical, physical strength and chemical resistance, are easy to work and simple to maintain. Arpa HPL panels are made of several layers of cellulose fibre material impregnated with thermosetting resins and then simultaneously subjected to both pressure (>7MPa)) and heat (140 / 150°C) in special presses, for a fixed time, which varies depending on the type of laminate. This process creates a stable, inert, homogeneous, nonporous and high density material, with physical and chemical properties that are totally different from those of its original ingredients. In addition, given its very low permeability, HPL acts as a barrier against the possible emission of formaldehyde and other volatile substances (VOCs) from any timber substrates it is applied to. Compos...

Medlum Density Fibre Board (MDF)

Medium Density Fibre Board (MDF)  MDF IS made from wood and other lignocellulose material refined into fibres and reconstituted with a resin binder. Row wood material is normally a single species wood. MDF has homogeneous structure with uniform density, texture and properties throughout, no identifiable grain can be seen at edge, end or face. There are no internal voids or pits and there is no variation in the surface hardness. Unlike plywood MDF doesn't delaminate. It has much higher strength than particle board. Since edges are totally smooth and uniform, costly tipping or beading with strips of wood required for plywood and particle board is not essential. It can be carved, grooved or embossed just like any timber. The surface of MDF is totally smooth and accepts all kinds of finishes - paints, varnishes and laminates. One such type of famous board in the market is 'Duratuff" . It comes in both interior and exterior grade. Duratuff prelaminated boards are also avail...

How to Calculate Cost and Quantity of 1000 Sq.ft Concrete Slab?

Cost and Quantity of 1000 Sq.ft Concrete Slab 1000 Sq.ft = 92.93 Sq.mt. Thickness of Slab = 0.150 Sq.mt. Volume of Slab = 92.93 X 0.150 = 13.939 cu.mt. Beam Volume = 20% o f concrete Vol.                         =13.939 X 20/100 = 2.7878 cu.mt. Total Slab Volume = 13.939 + 2.7878 = 16.768 = 17 cu.mt. We know :- M20 Grade of Concrete (1 : 1.5 : 3)  Concrete  Quantity  of 1 cu.mt. Cement = 8 bags   Sand = 15 cu.ft  aggregate = 30 cu.ft  1 cu.mt Concrete Cost =  4,550 Rs. So :- M20 Grade of Concrete (1 : 1.5 : 3)  Concrete  Quantity  of 1000 cu.mt. Cement = 17 X 8 = 136 bags  Sand = 17 X 15 = 255 cu.ft  aggregate = 30 X 17 = 510 cu.ft 1000 cu.mt Concrete Cost =  77,350 Rs. Steel Quantity = 1% of concrete Vol.                          =17 X 1/100 =...